The End !

Well, my Atlantis is now sold, awaiting collection from her new owner over the Easter holidays.
She will be heading to the North East of England, where I am sure she will enjoy her new life.

I am a little sad, to see her go, however my model boating days are now at an end, as I move on to pastures new in my modelling hobbies.

I would like offer my sincere thanks to Taylor Sparks in the USA for all his support and advice throught my build of the Robbe Atlantis.

Thank you so much Taylor ! :-)

Taylors web site is one of the few on the web that gave loads of information to Atlantis builders and owners, and certainly inspired me to make mine.

Check out Taylors fine web site here :

http://www.sparksstudios.com/boatyard/atlantis.htm

My web site link follows and is inspired by Taylors :

http://www.busybeas.pwp.blueyonder.co.uk/

Thanks also to Colin Harris in the UK for his occasional assistance.

I do hope you have enjoyed this blog account of the build of my Robbe Atlantis, and that is has helped or inspired you with yours, along the way.

All that remains is to say , thank you for watching !

Take Care, Keep Safe, God Bless

Stevie B

The journey to completion.

Having had a few days annual leave, the weather has been kind, so I resolved to complete the Atlantis ready for her "sale" .

I must confess, the Spring sunshine shows up her fine timbers and overall finish very well.

She is far from perfect, many mishaps /errors /frustrations along the way, but I am confident, her new owner ( whoever that may be?) will be delighted.

Equally, once she has been trimmed for sailing, she will inevitably gain an audience at the lakeside.

All that remains is for the new owner to complete the r/c installation, add the few remaining small fittings , trim, and sail away.

She does look as pretty as a picture... but my mind is set, and she must now go, as I move to other hobbies.

I sincerely hope that you have enjoyed my little build /blog and shared my frustrations as she comes to her conclusion.

This has at times been a very challenging kit, in no small part due to some poor quality materials, and my own frustrations / errors.

I am aware of several builders across the www, that my blog has helped with their own build, and it pleases me that you did benefit from my learning curve :-)

Here she is then, as she is prepared for "sale".

Bye for now

Stevie B

Contact made with another Atlantis owner

Many thanks to Cal Keen, for recent emails sharing his appreciation for my Atlantis blog efforts, which he has found very useful in his own build.

Thank you for the kind words... appreciated. Here is Cal's recent email to me :)

" Hello Steve,

A brief description of the photos:
Atlantis in van: I am lucky to have a vehicle large enough that I can transport the boat fully rigged.

Sheets inside hull, close-hauled: I made a tray that slides back to the rear of the hull, all the way to the rear pulley for the sail winch. This is so the sheets don't get tangled in the electronics.

Internal tray slid back showing carrying handle and electronics:
the carrying handle is the black tube shown in the picture. What I did was drill and tap 1/4" threads into the ballast weight, screw some bolts into it through the black aluminum tube. I can remove the cabin, slightly pay out the sails, slide the tray back, and carry the boat like a 38 lb. pc. of luggage.
It really works quite well. When I get to the pond, wearing high top rubber boots, I just set her in the water,slide the tray closed, set the cabin in place, and get underway. The pond where we sail is not subject to heavy seas, so I don't need the screwed down cover under the main cabin.

I am far from finished top-sides, but I am happy to be at the point of being able to sail.
I bought the Atlantis as a retirement gift to myself, 2 years ago. I did some work on her and then did other things for about a year. Now I have renewed interest in finishing the project.

I hope I haven't bored you with my notes and photos, I just want you to know that you have been somewhat of an inspiration to me to finish my project. I am looking forward to photos and notes of your finished Atlantis. Cal Keen "


Cheers for the input Cal !

Steve

Okay, it's been to cold to work in my shed, here in the UK.. well, I am getting older you know and I feel the cold more :)

Seriously, though.. with the cold weather, illness, and other interests, I just haven't found any inspiration to continue with the Atlantis.

More Bad News !!
I have decided that, the purchase of the Atlantis was a foolhardy one, logistically it is too big a model to lugg around and sail on my lonesome.

That, and my sailing buddy has decided to hang up his sails too. has led me to some serious thinking.I do not wish to sail alone, and haven't sailed since my last build ( Vaporetto) last Summer 2006. The" light/spark" call it what you will, has gone out, and I have lost interest in all things model boats.

I am going to complete the Atlantis in the near future, and aim to have her finished for the Easter break April 2007.

Then, she will be advertised on Ebay to be sold off to the highest bidder,with all the associated goodies, more details when I get that far !

Meanwhile, the final part of the build will begin again shortly.

Cheers
Steve